AGCO GT75The AGCO GT75 is a 2WD or 4WD utility tractor from the GT series. This tractor was manufactured by AGCO in Italy from 2004 to 2007. The AGCO GT75 is equipped with a 4.0 L (244.0 cu·in) four-cylinder diesel engine and a synchro-shuttle transmission with 16 forward and 8 reverse gears.

The AGCO GT75 utility tractor used the SAME Deutz-Fahr engine. It is a 4.0 L, 3,998 cm2, (244.0 cu·in) four-cylinder turbocharged diesel engine with 105.0 mm (4.13 in) of the cylinder bore and 115.0 mm (4.53 in) of the piston stroke. The compression ratio rating is 16.0:1. This engine produced 84.2 PS (61.9 kW; 83.0 HP) at 2,200 rpm of output power.

The AGCO GT75 is equipped with power steering, wet disc brakes, a two-post folding ROPS or cab (optional), and 89.7 liters (23.7 US gal.; 19.7 Imp. gal) fuel tank.

AGCO GT75 Specifications

General Specifications
Model AGCO GT75
Length 3,850 mm (151.6 in)
Width 1,940 mm (76.4 in)
Height 2,690 mm (105.9 in)
Wheel base 2WD: 2,230 mm (87.8 in)
4WD: 2,180 mm (85.8 in)
Weight 2WD ROPS: 2,500 kg (5,510 lbs)
4WD ROPS: 2,720 kg (6,000 lbs)
2WD Cab: 2,740 kg (6,040 lbs)
4WD Cab: 2,960 kg (6,525 lbs)

Fuel tank capacity 89.7 liters (23.7 US gal.; 19.7 Imp. gal)
Battery 12V
Cabin type Two-post folding ROPS or Cab (optional)
Engine model SAME Deutz-Fahr
Engine type Four-stroke, liquid-cooled, inline
Cylinders 4
Fuel type Diesel
Displacement 4.0 L, 3,998 cm2, (244.0 cu·in)
Bore and stroke 105.0 mm X 115.0 mm (4.13 in X 4.53 in)
Compression ratio 16.0:1
Horsepower 84.2 PS (61.9 kW; 83.0 HP) at 2,200 rpm
Torque 321.4 N·m (32.8 kg·m, 236.9 ft·lb) at 1,300 rpm
Starter Electric
Transmission and chassis
Chassis 4×2 2WD or 4×4 MFWD 4WD
Steering type Power
Brakes Wet disc
Transmission model
Transmission type Synchro-shuttle
Gears 16 forward and 8 reverse
Front tires
Rear tires
Three-Point Hitch
Category II
Control type
Lift capacity (at 610 mm/ 24 in) 1,600 kg (3,530 lbs)
PTO (Power take-off shaft)
Rear PTO type Independent with electro-hydraulic clutch
Rear PTO speed 540/1000 rpm
Hydraulic system
Hydraulic type Open center
Pump flow 14.0 gpm (53 lpm)
Total flow 22.7 gpm (85.9 lpm)
ATTENTION! Dear visitors, this site is not a trading platform, an official dealer or a spare parts supplier, so we do not have any price lists, spare parts catalogs, service or owner manuals. We are an information portal and provide the technical specifications.

We try to use verified sources and official documentation, however, differences between sources or errors in entering information may occur. In addition, the characteristics may vary depending on the modification and market. We do not provide advice on technical issues related to the any operation or repair. We do not recommend using provided information for repairing or spare parts ordering, use only official service manuals and spare-parts catalogs.

Be the first to comment

Leave a Reply

Your email address will not be published.