The John Deere 2210 is a 4WD sub-compact utility tractor manufactured by John Deere in Augusta, Georgia, USA from 2003 to 2006. The JD 2210 is equipped with a 1.0 L three-cylinder diesel engine and hydrostatic transmission with infinite (2-range) forward and reverse gears.
The JD 2210 sub-compact utility tractor used the Yanmar 3TNE74 engine. It is a 1 L, 1,001 cm2, (61.1 cu·in) three-cylinder natural aspirated diesel engine with 74.0 mm (2.91 in) of the cylinder bore and 78.0 mm (3.07 in) of the piston stroke. The compression ratio rating is 23.5:1. This engine produced 23.4 PS (17.2 kW; 23.0 HP) at 3,000 rpm of maximum output power.
The John Deere 2210 is equipped with power steering, wet disc brakes, open operator station with two-post ROPS and 19.0 liters (5 US gal.; 4.2 Imp. gal) fuel tank.
Following attachments are available for the John Deere 2210 sub-compact utility tractor:
- Mid-mount John Deere 54C 54 in (1,370 mm) mower deck with 3-blades
- Mid-mount John Deere 62D 62 in (1,570 mm) mower deck with 3-blades
- Front-mount John Deere 54 in (1,370 mm) blade
- Front-mount John Deere 46 in (1,160 mm) single-stage snow blower
- John Deere 210 loader
John Deere 2210 Specifications
General Specifications | |
Model | John Deere 2210 |
Length | 2,640 mm (103.9 in) |
Width | 1,210 mm (47.6 in) |
Height | 1,990 mm (78.3 in) |
Wheel base | 1,440 mm (56.7 in) |
Weight | 635 kg (1,400 lbs) |
Fuel tank capacity | 19.0 liters (5 US gal.; 4.2 Imp. gal) |
Battery | 12V, CCA 435A |
Cabin type | Open operator station with two-post ROPS |
Engine | |
Engine model | Yanmar 3TNE74 |
Engine type | Four-stroke, liquid-cooled, inline |
Cylinders | 3 |
Fuel type | Diesel |
Displacement | 1.0 L, 1,001 cm2, (61.1 cu·in) |
Bore and stroke | 74.0 mm X 78.0 mm (2.91 in X 3.07 in) |
Compression ratio | 23.5:1 |
Horsepower | 23.4 PS (17.2 kW; 23.0 HP) at 3,000 rpm |
Starter | Electric |
Oil type: | John Deere PLUS-4 or PLUS-50 |
Oil capacity: | 2.0 L (2.11 US. qt, 1.76 Imp. qt.) |
Coolant capacity: | 2.9 L (3.06 US. qt, 2.55 Imp. qt.) |
Transmission and chassis | |
Chassis | 4×4 MFWD 4WD |
Steering type | Power |
Brakes | Wet disc |
Final drive | Spur gear |
Differential lock | Mechanical rear |
Front axle | 2.5 L (2.64 US qts, 2.2 Imp. qts) |
Transmission model | – |
Transmission type | Hydrostatic |
Gears | Infinite (2-range) forward and reverse |
Speed | Forward: 13.7 kmh (8.5 mph) Reverse: 13.7 (8.5 mph) |
Transmission oil type | John Deere Low Viscosity HY-GARD (J20D) |
Transmission oil capacity | 13.0 L (3.4 US. gal, 2.9 Imp. gal.) |
Tires | |
Front tires | Ag: 18×8.50-10 |
Rear tires | Ag: 26×12.00-12 |
Three-Point Hitch | |
Caterogy | I |
Control type | – |
Lift capacity (at ends) | – |
PTO (Power take-off shaft) | |
Middle PTO type | Independent |
Middle PTO spped | 2,100 rpm |
Rear PTO type | Independent with hydraulic wet disc clutch |
Rear PTO spped | 540 rpm |
Hydraulic system | |
Hydraulic type | Open center |
Hydraulic capacity | 13.0 L (13.74 US. qt, 11.44 Imp. qt.) |
Pressure | 1,987 psi (137 bar) |
Valves | 2 |
Pump flow | 3.0 gpm (11.4 lpm) |
Steering flow | 2.5 gpm (9.5 lpm) |
Total flow | 5.5 gpm (20.8 lpm) |