The Mitsubishi MT180 is a 2WD or 4WD compact utility tractor manufactured by Mitsubishi from 1984 to 1991. The Mitsubishi MT180 is equipped with a 0.9 L (54.9 cu·in) three-cylinder diesel engine and one of two transmissions: a hydrostatic transmission with infinite (2-range) forward and reverse gears or a sliding gear transmission with 6 forward and 2 reverse gears.
The Mitsubishi MT180 compact utility tractor used the Mitsubishi K3C engine. It is a 0.9 L, 899 cm2, (54.9 cu·in) three-cylinder natural aspirated diesel engine with 70.0 mm (2.76 in) of the cylinder bore and 78.0 mm (3.07 in) of the piston stroke. The compression ratio rating is 23.0:1. This engine produced 18.8 PS (13.8 kW; 18.5 HP) at 2,700 rpm of output power.
The Mitsubishi MT180 is equipped with manual steering, drum brakes, an open operator station, and 18.2 liters (4.8 US gal.; 4 Imp. gal) fuel tank.
Mitsubishi MT180 variants:
- MT180 – 2WD Gear
- MT180D – 4WD Gear
- MT180HM – 2WD Hydro
- MT180HMD – 4WD Hydro
Mitsubishi MT180 Specifications
| General Specifications | |
| Model | Mitsubishi MT180 |
| Length | 2,220 mm (87.4 in) |
| Width | 2WD: 930 mm (36.6 in) 4WD: 970 mm (38.2 in) |
| Height (steering wheel) | 2WD: 1,170 mm (46.1 in) 4WD: 1,180 mm (46.5 in) |
| Wheel base | 1,420 mm (55.9 in) |
| Ground clearance | 2WD: 270 mm (10.6 in) 4WD: 210 mm (8.3 in) |
| Weight | 2WD: 575 kg (1,268 lbs) 4WD: 625 kg (1,378 lbs) |
| Fuel tank capacity | 18.2 liters (4.8 US gal.; 4 Imp. gal) |
| Battery | 12V, 45Ah |
| Cabin type | Open operator station |
| Engine | |
| Engine model | Mitsubishi K3C |
| Engine type | Four-stroke, liquid-cooled, inline |
| Cylinders | 3 |
| Fuel type | Diesel |
| Displacement | 0.9 L, 899 cm2, (54.9 cu·in) |
| Bore and stroke | 70.0 mm X 78.0 mm (2.76 in X 3.07 in) |
| Compression ratio | 23.0:1 |
| Horsepower | 18.8 PS (13.8 kW; 18.5 HP) at 2,700 rpm |
| Torque | 51.9 N·m (5.3 kg·m, 38.3 ft·lb) at 1,600 rpm |
| Starter | Electric |
| Oil capacity: | 3.0 L (3.2 US. qt, 2.6 Imp. qt.) |
| Coolant capacity: | 5.0 L (5.3 US. qt, 4.4 Imp. qt.) |
| Transmission and chassis | |
| Chassis | 4×2 2WD or 4×4 MFWD 4WD |
| Steering type | Manual |
| Brakes | Drum |
| Differential lock | Mechanical rear |
| Transmission model | – |
| Transmission type | Hydrostatic |
| Gears | Infinite (2-range) forward and reverse |
| Transmission model | – |
| Transmission type | Sliding gear |
| Gears | 6 forward and 2 reverse |
| Speed | Forward: 14.5 kmh (9 mph) Reverse: 6.9 kmh (4.3 mph) |
| Transmission oil capacity | 12.5 L (3.3 US. gal, 2.7 Imp. gal.) |
| Tires | |
| Front tires | Ag: 4.50-10 (2WD), 5-12 (4WD) |
| Rear tires | Ag: 8-18 |
| Three-Point Hitch | |
| Category | I |
| Control type | Position control |
| Lift capacity (at ends) | – |
| PTO (Power take-off shaft) | |
| Rear PTO type | – |
| Rear PTO speed | 540/1000 rpm |
| Hydraulic system | |
| Hydraulic type | Open center |
| Hydraulic capacity | 12.1 L (3.2 US. gal, 2.7 Imp. gal.) |
| Pressure | 1920 psi (132.4 bar) |
| Pump flow | 3.4 gpm (12.9 lpm) |
Bonjour. J’aurais besoin des 2 stabilisateurs pour maintenir les 2 bras du 3 points arriêre pour mon MT180 hmd. Si possible me dire a quel endroit me les procurer dans la région de Québec. Merci de votre attention.