The CaseIH 9110 is a four-wheel drive tractor from the 9100 series. This tractor was manufactured by CaseIH in Fargo, North Dakota, USA from 1986 to 1990. The CaseIH 9110 is equipped with a 8.3 L (505.0 cu·in) six-cylinder diesel engine and a full power shift transmission with hydraulic wet disc clutch and 12 forward and 2 reverse gears.
The CaseIH 9110 is equipped with hydrostatic power steering for steerable front axle and articulated chassis, hydraulic disc brakes brakes, cab (standard) with air-conditioning and 435.3 liters (115.0 US gal.; 95.8 Imp. gal) fuel tank.
Engine. The CaseIH 9110 four-wheel drive used the CDC 6CT 8.3 engine. It is a 8.3 L, 8,275 cm2, (505.0 cu·in) six-cylinder turbocharged diesel engine with 114.0 mm (4.49 in) of the cylinder bore and 135.0 mm (5.31 in) of the piston stroke. The compression ratio rating is 16.5:1. This engine produced 192.7 PS (141.7 kW; 190.0 HP) at 2,100 rpm of output power and 838.0 N·m (85.5 kg·m, 617.6 ft·lb) at 1,500 rpm of torque.
Transmission. The CaseIH 9110 is equipped with full power shift transmission with hydraulic wet disc clutch. The transmission has 12 forward (3.1-26.7 kmh; 2.0-16.6 mph) and 2 reverse gears (4.1-7.4 kmh; 2.5-4.6 mph).
Cab. The tractor used the standard cab with air-conditioning.
Dimensions and weight. The tractor has a length of 6,130 mm (241.3 in), a width of 3,030 mm (119.3 in), and a height of 3,290 mm (129.5 in), with a wheelbase of 3,050 mm (120.1 in) and a shipping weight of 7,711 kg (17,000 lbs). The front tires are 18.4-38 and rear tires are 18.4-38. Ground clearance is 520 mm (20.5 in).
Hydraulic system. The hydraulic lift has a Category III (optional) three-point linkage and a maximum lifting capacity of 5,783 kg (12,752 lbs) at the link end. It also has a rear, independent type power take-off shaft (PTO) with a speed of 1,000 rpm. The hydraulic system is a closed center type with a hydraulic fluid capacity of 68.1 liters (18.0 US. gal, 15.0 Imp. gal.), a pressure of 2500 psi (172.4 bar). The total flow rate is 102.2 gpm (386.9 lpm).
General Specifications
| General Specifications | |
| Tractor type | Four-wheel drive (4WD) tractor |
| Production years | 1986-1990 |
| Manufacturer | Case IH |
| Factory | Fargo, North Dakota, USA |
| Dimensions and weight | |
| Length | 6,130 mm (241.3 in) |
| Width | 3,030 mm (119.3 in) |
| Height (exhaust) | 3,290 mm (129.5 in) |
| Wheelbase | 3,050 mm (120.1 in) |
| Ground clearance | 520 mm (20.5 in) |
| Weight (shipping) | 7,711 kg (17,000 lbs) |
| Fluid capacity | |
| Fuel tank capacity | 435 liters (115.0 US gal, 95.7 Imp. gal) |
| Oil capacity | 20.8 liters (22.0 US.qts, 18.3 Imp. qts) |
| Coolant capacity | 33.2 liters (35.0 US.qts, 29.2 Imp. qts) |
| Hydraulic luid capacity: | 68.0 liters (18.0 US gal, 15.0 Imp. gal) |
| Electrical system | |
| Ground | Negative |
| Charging system | Alternator |
| Charging amps | 105 |
| Battery | Two 12V |
| Cabin type | |
| Cabin type | Standard: Cab with air-conditioning |
Engine
| Engine | |
| Engine model | CDC 6CT 8.3 |
| Engine type | Four-stroke, liquid-cooled, inline |
| Cylinders | 6 |
| Fuel type | Diesel |
| Displacement | 8.3 L, 8,275 cm2, (505.0 cu·in) |
| Bore and stroke | 114.0 mm X 135.0 mm (4.49 in X 5.31 in) |
| Compression ratio | 16.5:1 |
| Horsepower | 192.7 PS (141.7 kW; 190.0 HP) at 2,100 rpm |
| Torque | 838.0 N·m (85.5 kg·m, 617.6 ft·lb) at 1,500 rpm |
| Starter | Electric |
| Oil capacity: | 20.8 L (22 US. qt, 18.3 Imp. qt.) |
| Coolant capacity: | 33.3 L (35.2 US. qt, 29.3 Imp. qt.) |
Transmission and chassis
| Transmission and chassis | |
| Chassis | 4×4 4WD |
| Steering type | Hydrostatic power for steerable front axle and articulated chassis |
| Brakes | Hydraulic disc brakes |
| Final drive | Inboard planetary |
| Transmission model | – |
| Transmission type | Full power shift with hydraulic wet disc clutch |
| Gears | 12 forward and 2 reverse |
| Speed | Forward: 26.7 kmh (16.6 mph) Reverse: 7.4 kmh (4.6 mph) |
Tires
| Tires | |
| Front tires | Ag: 18.4-38 |
| Rear tires | Ag: 18.4-38 |
PTO and 3-point linkage
| Three-Point Hitch | |
| Category | III (optional) |
| Control type | – |
| Lift capacity (at ends) | 5,783 kg (12,752 lbs) |
| PTO (Power take-off shaft) | |
| Rear PTO type | Independent (optional) |
| Rear PTO speed | 1000 rpm |
Hydraulic system
| Hydraulic system | |
| Hydraulic type | Closed center |
| Hydraulic capacity | 68.1 L (18 US. gal, 15 Imp. gal.) |
| Pressure | 2500 psi (172.4 bar) |
| Valves | 2 to 4 |
| Total flow | 102.2 gpm (386.9 lpm) |
CaseIH 9110 reviews
[site_reviews form=”14865″ assigned_posts=”post_id”]
Be the first to comment