CaseIH 7250

CaseIH 7250The CaseIH 7250 Magnum is a 4WD row-crop tractor from the Magnum 7200 series. This tractor was manufactured by CaseIH in Racine, Wisconsin, USA from 1994 to 1996. The CaseIH 7250 is equipped with a 8.3 L (504.5 cu·in) six-cylinder diesel engine and a full power shift transmission with 18 forward and 4 reverse gears (24 forward and 6 reverse with creeper).

The Case International 7250 row-crop tractor used the CDC engine. It is a 8.3 L, 8,267 cm2, (504.5 cu·in) six-cylinder turbocharged intercooled diesel engine with 114.0 mm (4.49 in) of the cylinder bore and 135.0 mm (5.31 in) of the piston stroke. The compression ratio rating is 16.5:1. This engine produced 218.0 PS (160.3 kW; 215.0 HP) at 2,200 rpm of PTO output power.

The CaseIH 7250 is equipped with power steering, differential hydraulic wet disc brakes, cab (standard) with air-conditioning and 359.6 liters (95.0 US gal.; 79.1 Imp. gal) fuel tank.

CaseIH 7250 Specifications

General Specifications
Model CaseIH 7250 Magnum
Length
Width
Height
Wheel base 3,000 mm (118.1 in)
Ground clearance (front axle) 490 mm (19.3 in)
Weight (operating) 8,230 kg (18,144 lbs)
Fuel tank capacity 359.6 liters (95 US gal.; 79.1 Imp. gal)
Battery Two 12V, CCA 950A
Cabin type Cab (standard) with air-conditioning
Engine
Engine model CDC
Engine type Four-stroke, liquid-cooled, inline
Cylinders 6
Fuel type Diesel
Displacement 8.3 L, 8,267 cm2, (504.5 cu·in)
Bore and stroke 114.0 mm X 135.0 mm (4.49 in X 5.31 in)
Compression ratio 16.5:1
Horsepower 218 PS (160.3 kW; 215.0 HP) at 2,200 rpm
Starter Electric
Oil capacity: 20.8 L (22 US. qt, 18.3 Imp. qt.)
Coolant capacity: 29.3 L (31 US. qt, 25.8 Imp. qt.)
Transmission and chassis
Chassis 4×4 MFWD 4WD
Steering type Power
Brakes Differential hydraulic wet disc
Differential lock Electric rear
Transmission model
Transmission type Full power shift with hydraulic wet disc clutch
Gears 18 forward and 4 reverse
Speed Forward: 32.8 kmh (20.4 mph) Reverse: 11.9 kmh (7.4 mph)
Tires
Front tires Ag: 16.9-28
Rear tires Ag: 20.8R-38
Three-Point Hitch
Category III
Control type Electronic lower-link draft sensing
Lift capacity 6,780 kg (14,950 lbs)
PTO (Power take-off shaft)
Rear PTO type Independent with hydraulic wet disc clutch
Rear PTO speed 1000 (1.75)
Hydraulic system
Hydraulic type Closed center pressure flow compensated (PFC)
Hydraulic capacity 172.2 L (45.5 US. gal, 37.9 Imp. gal.)
Pressure 2300 psi (158.6 bar)
Valves 3 or 4
SCV flow 22.0 gpm (83.3 lpm)
Total flow 29.0 gpm (109.8 lpm)
ATTENTION! Dear visitors, this site is not a trading platform, an official dealer or a spare parts supplier, so we do not have any price lists, spare parts catalogs, service or owner manuals. We are an information portal and provide the technical specifications.

We try to use verified sources and official documentation, however, differences between sources or errors in entering information may occur. In addition, the characteristics may vary depending on the modification and market. We do not provide advice on technical issues related to the any operation or repair. We do not recommend using provided information for repairing or spare parts ordering, use only official service manuals and spare-parts catalogs.

Be the first to comment

Leave a Reply

Your email address will not be published.


*