John Deere 2520 (2006-2012)

John Deere 2520 (2006-2012)The John Deere 2520 is a 4WD compact utility tractor from the 2000 Twenty series. This tractor was manufactured by the John Deere in Augusta, Georgia, USA from 2006 to 2012. The John Deere 2520 utility tractor is equipped with a 1.3 L three-cylinder diesel engine and hydrostatic transmission with infinite (2-range) forward and reverse gears.

The John Deere 2520 compact utility tractor used the Yanmar 3TNV82A engine. It is a 1.3 L, 1,331 cm2, (81.2 cu·in) three-cylinder natural aspirated diesel engine with 82.0 mm (3.23 in) of the cylinder bore and 84.0 mm (3.31 in) of the piston stroke. The compression ratio rating is 19.2:1. The 3TNV82A engine produced 26.8 PS (19.7 kW; 26.4 HP) at 2,600 rpm of gross output power and 69.6 N·m (7.1 kg·m, 51.3 ft·lb) at 2,600 rpm of maximum torque.

The JD 2520 is equipped with power steering, wet disc brakes, open operator station with two-post ROPS and 27.0 liters (7.1 US gal.; 5.9 Imp. gal) fuel tank.

Following attachments are available for the John Deere 2520 compact utility tractor:

  • Mid-mount John Deere 62D2: 62 in (1,570 mm) mower deck with 3-blades
  • Mid-mount John Deere 72: 72 in (1,820 mm) mower deck with 3-blades
  • John Deere 200CX loader
  • John Deere 46 backhoe

John Deere 2520 Specifications

General Specifications
Model John Deere 2520
Length 2,760 mm (108.7 in)
Width 1,330 mm (52.4 in)
Height 2,270 mm (89.4 in)
Wheel base 1,650 mm (65 in)
Weight 845 kg (1,863 lbs)
Fuel tank capacity 27.0 liters (7.1 US gal.; 5.9 Imp. gal)
Battery 12V, CCA 500A
Cabin type Open operator station with two-post ROPS
Engine model Yanmar 3TNV82A
Engine type Four-stroke, liquid-cooled, inline
Cylinders 3
Fuel type Diesel
Displacement 1.3 L, 1,331 cm2, (81.2 cu·in)
Bore and stroke 82.0 mm X 84.0 mm (3.23 in X 3.31 in)
Compression ratio 19.2:1
Horsepower 26.8 PS (19.7 kW; 26.4 HP) at 2,600 rpm
Torque 69.6 N·m (7.1 kg·m, 51.3 ft·lb) at 2,600 rpm
Starter Electric
Oil capacity: 3.6 L (3.8 US. qt, 3.2 Imp. qt.)
Coolant capacity: 3.9 L (4.1 US. qt, 3.4 Imp. qt.)
Transmission and chassis
Chassis 4×4 4WD
Steering type Power
Brakes Wet disc
Final drive Spur gear
Front axle 3.4 liters (3.6 US.qts, 3.0 Imp. qts)
Transmission model
Transmission type Hydrostatic
Gears Infinite (2-range) forward and reverse
Speed Forward: 20.9 kmh (13 mph) Reverse: 20.9 (13 mph)
Transmission oil capacity 14.8 L (3.9 US. gal, 3.3 Imp. gal.)
Front tires Lawn/turf: 24×8.5-14
Industrial: 23×8.5-12
Rear tires Lawn/turf: 36×14.00-15
Industrial: 14-17.5
Three-Point Hitch
Caterogy I
Control type Position control
Lift capacity (at ends) 650 kg (1,433 lbs)
PTO (Power take-off shaft)
Middle PTO type Standard
Middle PTO spped 1,000 rpm
Rear PTO type Independent
Rear PTO spped 540 rpm
Hydraulic system
Hydraulic type Open center
Hydraulic capacity 14.6 L (15.43 US. qt, 12.85 Imp. qt.)
Valves 2
Pump flow 5.0 gpm (18.9 lpm)
Steering flow 5.5 gpm (20.8 lpm)
Total flow 10.5 gpm (39.7 lpm)
ATTENTION! Dear visitors, this site is not a trading platform, an official dealer or a spare parts supplier, so we do not have any price lists, spare parts catalogs, service or owner manuals. We are an information portal and provide the technical specifications.

We try to use verified sources and official documentation, however, differences between sources or errors in entering information may occur. In addition, the characteristics may vary depending on the modification and market. We do not provide advice on technical issues related to the any operation or repair. We do not recommend using provided information for repairing or spare parts ordering, use only official service manuals and spare-parts catalogs.

Be the first to comment

Leave a Reply

Your email address will not be published.