John Deere 5010

John Deere 5010The John Deere 5010 is a 2WD standard-tread tractor from the New Generation series. This tractor was manufactured by John Deere in Waterloo, Iowa, USA from 1963 to 1965. The John Deere 5010 is equipped with a 8.7 L (531.0 cu·in) six-cylinder diesel engine and a syncro-range transmission with 8 forward and 3 reverse gears.

The John Deere 5010 standard-tread tractor used the John Deere engine. It is a 8.7 L, 8,701 cm2, (531.0 cu·in) six-cylinder natural aspirated diesel engine with 121.0 mm (4.76 in) of the cylinder bore and 127.0 mm (5 in) of the piston stroke. The compression ratio rating is 16.0:1. This engine produced 122.7 PS (90.2 kW; 121.0 HP) at 2,200 rpm of PTO output power.

The JD 5010 is equipped with power steering, hydraulic wet disc brakes, open operator station, and 182.0 liters (48.1 US gal.; 40 Imp. gal) fuel tank.

John Deere 5010 Specifications

General Specifications
Model John Deere 5010
Length 4,370 mm (172 in)
Width 2,430 mm (95.7 in)
Height 2,440 mm (96.1 in)
Wheel base 2,640 mm (103.9 in)
Ground clearance 400 mm (15.7 in)
Weight (operating) 5,860 kg (12,920 lbs)
Fuel tank capacity 182.0 liters (48.1 US gal.; 40 Imp. gal)
Battery Four 6V, 115Ah
Cabin type Open operator station
Engine
Engine model John Deere
Engine type Four-stroke, liquid-cooled, inline
Cylinders 6
Fuel type Diesel
Displacement 8.7 L, 8,701 cm2, (531.0 cu·in)
Bore and stroke 121.0 mm X 127.0 mm (4.76 in X 5 in)
Compression ratio 16.0:1
Horsepower 122.7 PS (90.2 kW; 121.0 HP) at 2,200 rpm
Starter Electric
Oil capacity: 11.4 L (12 US. qt, 10 Imp. qt.)
Coolant capacity: 32.2 L (34 US. qt, 28.3 Imp. qt.)
Transmission and chassis
Chassis 4×2 2WD
Steering type Power
Brakes Hydraulic wet disc
Transmission model
Transmission type Syncro-Range
Gears 8 forward and 3 reverse
Speed Forward: 28.6 kmh (17.8 mph) Reverse: 16.9 (10.5 mph)
Transmission oil capacity 64.4 L (17 US. gal, 14.2 Imp. gal.)
Tires
Front tires Ag: 11.00-16
Rear tires Ag: 24.5-32
Three-Point Hitch
Caterogy III/II
Control type
Lift capacity (at ends)
PTO (Power take-off shaft)
Rear PTO type Independent
Rear PTO speed 1,000 rpm
Hydraulic system
Hydraulic type Closed center
Hydraulic capacity 64.4 L (17.0 US. gal, 14.2 Imp. gal.)
Pressure 2250 psi (155.1 bar)
Valves 1 or 2
Pump flow 20.0 gpm (75.7 lpm)
ATTENTION! Dear visitors, this site is not a trading platform, an official dealer or a spare parts supplier, so we do not have any price lists, spare parts catalogs, service or owner manuals. We are an information portal and provide the technical specifications.

We try to use verified sources and official documentation, however, differences between sources or errors in entering information may occur. In addition, the characteristics may vary depending on the modification and market. We do not provide advice on technical issues related to the any operation or repair. We do not recommend using provided information for repairing or spare parts ordering, use only official service manuals and spare-parts catalogs.

Be the first to comment

Leave a Reply

Your email address will not be published.


*